Miller Effect In Mosfet

Miller Effect In Mosfet Science
Miller Capacitance Mosfet
Miller Capacitance Effect In Mosfet
Miller Effect In Mosfet Diagram
Miller Effect In Mosfet Value

The Miller capacitance (reverse transfer capacitance) is usually the smallest but it can have a serious effect on performance. Consider the MOSFET above switching a 10A load from a supply voltage of 50V. If you drive the gate to turn the device on the drain could be expected to fall from 50V to 0V within a few hundred nano seconds. In fact, a very rough estimate of bandwidth due to Miller effect (without resorting to the full Miller approximation given before) is: (6.53) ω h ≈ 1 R s (A C μ 1) ≈ 1 (2000) (100) (2 × 10 − 12) ≈ 2.5 Mrad / s f h ≈ ω h 2 π ≈ 398 kHz which is a pretty good estimate since it is so simple and intuitive. Similar to the GTO, the IGBT can be used to block both positive and negative voltages. Operating currents are fairly high, in excess of 1500 A and switching voltage up to 3000 V. The IGBT has reduced input capacitance compared to MOSFET devices which improves the Miller feedback effect during high dv/dt turn on and turn off.

In electronics, the Miller effect accounts for the increase in the equivalent inputcapacitance of an inverting voltage amplifier due to amplification of the effect of capacitance between the input and output terminals. The virtually increased input capacitance due to the Miller effect is given by

{displaystyle C_{M}=C(1+A_{v}),}

where ${displaystyle -A_{v}}$ is the voltage gain of the inverting amplifier ( ${displaystyle A_{v}}$ positive) and ${displaystyle C}$ is the feedback capacitance.

Although the term Miller effect normally refers to capacitance, any impedance connected between the input and another node exhibiting gain can modify the amplifier input impedance via this effect. These properties of the Miller effect are generalized in the Miller theorem. The Miller capacitance due to parasitic capacitance between the output and input of active devices like transistors and vacuum tubes is a major factor limiting their gain at high frequencies. Miller capacitance was identified in 1920 in triodevacuum tubes by John Milton Miller.

History[edit]

The Miller effect was named after John Milton Miller.^[1] When Miller published his work in 1920, he was working on vacuum tube triodes; however, the same theory applies to more modern devices such as bipolar junction and field-effect transistors.

Derivation[edit]

Figure 1: An ideal voltage inverting amplifier with an impedance connecting output to input.

Consider an ideal inverting voltage amplifier of gain ${displaystyle A_{v}}$ with an impedance ${displaystyle Z}$ connected between its input and output nodes. The output voltage is therefore ${displaystyle V_{o}=-A_{v}V_{i}}$ . Assuming that the amplifier input draws no current, all of the input current flows through ${displaystyle Z}$ , and is therefore given by

{displaystyle I_{i}={frac {V_{i}-V_{o}}{Z}}={frac {V_{i}(1+A_{v})}{Z}}}

The input impedance of the circuit is

{displaystyle Z_{in}={frac {V_{i}}{I_{i}}}={frac {Z}{1+A_{v}}}}

If ${displaystyle Z}$ represents a capacitor with impedance ${displaystyle Z={frac {1}{sC}}}$ , the resulting input impedance is

{displaystyle Z_{in}={frac {1}{sC_{M}}}quad mathrm {where} quad C_{M}=C(1+A_{v})}

Thus the effective or Miller capacitanceC_M is the physical C multiplied by the factor ${displaystyle (1+A_{v})}$ .^[2]

Effects[edit]

As most amplifiers are inverting ( ${displaystyle A_{v}}$ as defined above is positive), the effective capacitance at their inputs is increased due to the Miller effect. This can reduce the bandwidth of the amplifier, restricting its range of operation to lower frequencies. The tiny junction and stray capacitances between the base and collector terminals of a Darlington transistor, for example, may be drastically increased by the Miller effects due to its high gain, lowering the high frequency response of the device.

It is also important to note that the Miller capacitance is the capacitance seen looking into the input. If looking for all of the RC time constants (poles) it is important to include as well the capacitance seen by the output. The capacitance on the output is often neglected since it sees ${displaystyle {C}({1+1/A_{v}})}$ and amplifier outputs are typically low impedance. However if the amplifier has a high impedance output, such as if a gain stage is also the output stage, then this RC can have a significant impact on the performance of the amplifier. This is when pole splitting techniques are used.

Miller Effect In Mosfet Science

The Miller effect may also be exploited to synthesize larger capacitors from smaller ones. One such example is in the stabilization of feedback amplifiers, where the required capacitance may be too large to practically include in the circuit. This may be particularly important in the design of integrated circuits, where capacitors can consume significant area, increasing costs.

Mitigation[edit]

The Miller effect may be undesired in many cases, and approaches may be sought to lower its impact. Several such techniques are used in the design of amplifiers.

A current buffer stage may be added at the output to lower the gain ${displaystyle A_{v}}$ between the input and output terminals of the amplifier (though not necessarily the overall gain). For example, a common base may be used as a current buffer at the output of a common emitter stage, forming a cascode. This will typically reduce the Miller effect and increase the bandwidth of the amplifier.

Alternatively, a voltage buffer may be used before the amplifier input, reducing the effective source impedance seen by the input terminals. This lowers the ${displaystyle RC}$ time constant of the circuit and typically increases the bandwidth.

The Miller capacitance can be mitigated by employing neutralisation. This can be achieved by feeding back an additional signal that is in phase opposition to that which is present at the stage output. By feeding back such a signal via a suitable capacitor, the Miller effect can, at least in theory, be eliminated entirely. In practice, variations in the capacitance of individual amplifying devices coupled with other stray capacitances, makes it difficult to design a circuit such that total cancellation occurs. Historically, it was not unknown for the neutralising capacitor to be selected on test to match the amplifying device, particularly with early transistors that had very poor bandwidths. The derivation of the phase inverted signal usually requires an inductive component such as a choke or an inter-stage transformer.

In vacuum tubes, an extra grid (the screen grid) could be inserted between the control grid and the anode. This had the effect of screening the anode from the grid and substantially reducing the capacitance between them. While the technique was initially successful other factors limited the advantage of this technique as the bandwidth of tubes improved. Later tubes had to employ very small grids (the frame grid) to reduce the capacitance to allow the device to operate at frequencies that were impossible with the screen grid.

Impact on frequency response[edit]

Figure 2: Amplifier with feedback capacitor C_C.

Miller Capacitance Mosfet

Figure 2A shows an example of Figure 1 where the impedance coupling the input to the output is the coupling capacitor C_C. A Thévenin voltage source V_A drives the circuit with Thévenin resistance R_A. The output impedance of the amplifier is considered low enough that the relationship V_o= -A_vV_i is presumed to hold. At the output Z_L serves as the load. (The load is irrelevant to this discussion: it just provides a path for the current to leave the circuit.) In Figure 2A, the coupling capacitor delivers a current jωC_C(V_i − V_o) to the output node.

Figure 2B shows a circuit electrically identical to Figure 2A using Miller's theorem. The coupling capacitor is replaced on the input side of the circuit by the Miller capacitance C_M, which draws the same current from the driver as the coupling capacitor in Figure 2A. Therefore, the driver sees exactly the same loading in both circuits. On the output side, a capacitor C_Mo = (1 + 1/A_v)C_C draws the same current from the output as does the coupling capacitor in Figure 2A.

In order for the Miller capacitance to draw the same current in Figure 2B as the coupling capacitor in Figure 2A, the Miller transformation is used to relate C_M to C_C. In this example, this transformation is equivalent to setting the currents equal, that is

{displaystyle jomega C_{C}(V_{i}-V_{O})=jomega C_{M}V_{i},}

or, rearranging this equation

{displaystyle C_{M}=C_{C}left(1-{frac {V_{o}}{V_{i}}}right)=C_{C}(1+A_{v}).}

This result is the same as C_M of the Derivation Section.

Miller Capacitance Effect In Mosfet

The present example with A_v frequency independent shows the implications of the Miller effect, and therefore of C_C, upon the frequency response of this circuit, and is typical of the impact of the Miller effect (see, for example, common source). If C_C = 0 F, the output voltage of the circuit is simply A_v v_A, independent of frequency. However, when C_C is not zero, Figure 2B shows the large Miller capacitance appears at the input of the circuit. The voltage output of the circuit now becomes

{displaystyle V_{o}=-A_{v}V_{i}=-A_{v}{frac {V_{A}}{1+jomega C_{M}R_{A}}},}

and rolls off with frequency once frequency is high enough that ωC_MR_A ≥ 1. It is a low-pass filter. In analog amplifiers this curtailment of frequency response is a major implication of the Miller effect. In this example, the frequency ω_3dB such that ω_3dBC_MR_A = 1 marks the end of the low-frequency response region and sets the bandwidth or cutoff frequency of the amplifier.

The effect of C_M upon the amplifier bandwidth is greatly reduced for low impedance drivers (C_MR_A is small if R_A is small). Consequently, one way to minimize the Miller effect upon bandwidth is to use a low-impedance driver, for example, by interposing a voltage follower stage between the driver and the amplifier, which reduces the apparent driver impedance seen by the amplifier.

The output voltage of this simple circuit is always A_v v_i. However, real amplifiers have output resistance. If the amplifier output resistance is included in the analysis, the output voltage exhibits a more complex frequency response and the impact of the frequency-dependent current source on the output side must be taken into account.^[3] Ordinarily these effects show up only at frequencies much higher than the roll-off due to the Miller capacitance, so the analysis presented here is adequate to determine the useful frequency range of an amplifier dominated by the Miller effect.

Miller approximation[edit]

This example also assumes A_v is frequency independent, but more generally there is frequency dependence of the amplifier contained implicitly in A_v. Such frequency dependence of A_v also makes the Miller capacitance frequency dependent, so interpretation of C_M as a capacitance becomes more difficult. However, ordinarily any frequency dependence of A_v arises only at frequencies much higher than the roll-off with frequency caused by the Miller effect, so for frequencies up to the Miller-effect roll-off of the gain, A_v is accurately approximated by its low-frequency value. Determination of C_M using A_v at low frequencies is the so-called Miller approximation.^[2] With the Miller approximation, C_M becomes frequency independent, and its interpretation as a capacitance at low frequencies is secure.

References and notes[edit]

Miller Effect In Mosfet Diagram

^John M. Miller, 'Dependence of the input impedance of a three-electrode vacuum tube upon the load in the plate circuit,' Scientific Papers of the Bureau of Standards,vol.15, no. 351, pages 367-385 (1920). Available on-line at: http://web.mit.edu/klund/www/papers/jmiller.pdf .
^ ^a^bR.R. Spencer and M.S. Ghausi (2003). Introduction to electronic circuit design. Upper Saddle River NJ: Prentice Hall/Pearson Education, Inc. p. 533. ISBN0-201-36183-3.
^See article on pole splitting.

Goldfox724